View cart

How to Seal a Pinhole Leak with Liquid Lex

Part 1: Find and mark the leak

The easiest way to spot a pinhole is to let the raft show you where it leaks. Spray the inflated tube with soapy water and watch where a bubble keeps growing. Here’s how we marked that spot on a yellow SOTAR thwart.

Prepping the urethane and sealing it with Liquid Lex.

For prep: Set out a pump and gauge, diluted dish soap, a spray bottle, a grease pencil, a lint-free cotton rag and solvent-resistant masking tape.

1. Inflate the tube

Bring the tube to its recommended pressure so air can escape through the pinhole. We use 3 psi on the tube in this demo. Check the pressure specified for your own boat and chamber.

Watch this step · 0:11

2. Find the bubbles

Spray diluted dish soap over the suspected area. Watch for bubbles that keep growing in one spot. That spot is where air is escaping.

Watch this step · 0:18

3. Mark the spot before wiping

Circle each leak with a grease pencil while you can still see the bubbles. Wipe the area dry with a lint-free cotton rag, then renew the mark so you can find it again.

Watch this step · 0:27

4. Mask a rounded repair area

Leave a margin of exposed fabric around the pinholes. Round the corners of the masking window so the finished coating has fewer edges that can lift. On a sloping tube, fold the lower tape edge up to catch drips.

Watch this step · 0:55

Watch Part 1 on YouTube


Part 2: Cleaning

Clean the exposed urethane

The goal is a small, evenly prepared area of fabric. The shine left after the solvent evaporates tells you when to stop. Be careful not to scrub too much or you will expose the white base cloth.

For cleaning: Set out clean THF, lint-free cotton rags, solvent-resistant masking tape and your protective equipment.

Before opening the solvent: Tetrahydrofuran (THF) is the cleaning solvent used in this demo and an ingredient in Liquid Lex. Its vapors are highly flammable. Work in a well-ventilated area away from heat, sparks and flames. Follow the product safety data sheets and use splash goggles and gloves rated for THF.

5. Use two rags to control the solvent

Wipe inside the taped area with a THF-dampened, lint-free cotton rag. Hold a dry rag just below it to catch drips before they reach the rest of the tube.

Watch this step · 0:16

6. Look for a lasting shine

Use light pressure and work slowly to lift the cloudy surface layer. Let the solvent evaporate. The prepared urethane should still look shiny and feel tacky. Keep your solvent-rated gloves on when checking it.

Watch this step · 0:52

7. Give stubborn spots another pass

If one strip stays cloudy, mask around it so you can work just that spot. Remove the temporary strip when you finish, and leave the outer tape and drip dam in place for coating.

Watch this step · 1:22

Watch Part 2 on YouTube


Part 3: Applying Liquid Lex

Roll on the first coat

Set up your roller and find the valve before coating the tube. Once the surface is wet with THF, you’ll want the roller ready.

For coating: Gather clear Liquid Lex, clean THF, a lint-free paint roller and frame, and a timer.

8. Load the roller

Have the timer and clean THF within reach. Coat a lint-free roller with clear Liquid Lex before you wet the prepared tube. That way you can roll the first coat on immediately.

Watch this step · 0:15

9. Wet the surface and roll the first coat

Wipe clean THF over the prepared area. Immediately roll on a thin, even coat of Liquid Lex with a lint-free roller. This is the only coat that gets a fresh THF wipe first.

Watch this step · 0:29

10. Let a little air out

After the first coat, release some air from the tube as shown in the video. Leave the masking in place while the coating builds.

Watch this step · 0:38

Watch Part 3 on YouTube

Finishing the repair

Finish the coats and check for leaks

Keep the repair in the shade or under cover while you build the coating.

11. Build up six thin coats

Keep the repair in the shade or under cover. Wait 10–15 minutes between coats. Use clear Liquid Lex for the first four coats. The last two can be clear or colored, for six coats total. Temperature should be between 50 and 100 degrees. The hotter it is the faster the Lex will dry.

Watch this step · 1:05

12. Wait 30 minutes and peel the tape

After the last coat, let the coating dry for 30 minutes before peeling away the masking tape and drip dam.

Watch this step · 1:27

13. Repeat the soap test

Check the repaired spot with diluted dish soap again. A bubble that keeps growing means air is still escaping. If it does, keep the boat ashore and contact our repair team. Follow the product cure guidance before returning the boat to the water.

Watch this step · 1:32

Working on a split seam, a tear, or a boat with unknown fabric? Send a photo to our repair team before choosing a repair method. Email SOTAR Service.

Liquid Lex urethane paint · SOTAR repair services