TEAR REPAIR INSTRUCTIONS
When a raft tube goes soft and you can’t see a hole, the handiest tool in your repair kit might be a little dish soap. Once you find the leak, a clear Tear-Aid patch can cover a pinhole or small tear in the fabric. Here’s how we walk boaters through it, from the first bubbles to the final pressure check.
Before you open the kit
Choose the patch by the surface it will touch. Use Type A for urethane, including SOTAR urethane raft fabric. Use Type B for vinyl or PVC. If you’re working on an older boat and don’t know the fabric, check its owner’s manual or ask the manufacturer before peeling the backing.
(NOTE that both A and B will work. A is not as sticky right off but once cured it better for longevity. Type B is stickier for wetter situations and need a faster application)
Set out your patch, blunt-tip scissors, and an alcohol prep pad. A clean cloth with equal parts isopropyl rubbing alcohol and water also works. Your fingers can press the patch down, or you can use a smooth roller.
See the SOTAR patch kit · Find Type A and Type B patches
Use Tear-Aid as a temporary field repair for minor fabric damage. If a seam is opening, the valve is leaking, or anyone’s safety depends on this patch holding, keep the raft ashore and contact the repair team.
How do I find a pinhole I can’t see?
With the raft ashore and the tube still inflated, spray a little diluted dish soap over the suspected spot. Watch for a cluster of bubbles that keeps growing in one place. Mark just outside the area the patch will cover so you can find the hole again when the tube goes flat. Rinse away the soap, then deflate the raft according to its owner’s manual before patching.
Step 1. Clean beyond the tear
Lay the damaged fabric flat. Wipe away sand or grit, then clean the whole patch footprint with your alcohol pad or alcohol-and-water mix. Let it air-dry completely, including the margins where the edges will stick. Tear-Aid specifies a fabric surface temperature of at least 50°F (10°C) for dry application.

Clean a little farther out than you expect the patch to reach.
Step 2. Cut a patch with room on every side
Leave the backing on and center the patch over the damage to check the fit. You need at least 1 inch of sound fabric beyond every edge. For a 1-inch straight tear, cut a patch at least 3 inches long and wide enough to leave the same margin above and below. Round all four corners with scissors. If you use two pieces, overlap them by at least 1 inch.

Measure from the tips of the tear. A rounded corner gives grit and gear less edge to catch.
Step 3. Peel back half an inch
Turn the patch over and peel back about ½ inch of the paper liner at one edge. Hold the rest by the backing to keep your fingers off the adhesive. Before that sticky strip touches the raft, check that the far end of the patch will still clear the tear by a full inch.

The liner doubles as a handle while you line up the first edge.
Step 4. Anchor, smooth, and press
Press the exposed strip onto clean fabric beyond the tear. With one hand, slowly draw the liner back. With the other, smooth each newly exposed section onto the raft as you go. Work out trapped air toward the nearest edge. Once the patch lies flat, rub firmly across the center and all the way around the perimeter with your fingers or roller.

Make one last pass around the perimeter, including each rounded corner.
How to patch a raft tear from the inside and outside
Both patches cover the same tear in one tube wall. Apply the inside patch first while the opening is still accessible. Use this method for a small tear only if you can reach, clean, and press the entire inside patch flat. For a pinhole too small to reach through, leave it its original size and use the outside-patch steps above.
- Prepare both faces. Bring the raft ashore and deflate it. Wipe the inside and outside around the tear with an alcohol prep pad or equal parts rubbing alcohol and water. Let both faces dry completely.
- Cut and test-fit two patches. Round the corners of each patch. Each one needs at least 1 inch of sound fabric past the tear in every direction. With both liners still on, slip the first patch through the existing opening. Check that you can center it behind the tear, reach its edges, and draw the liner back out. Then take it out for the next step.
- Set the inside patch. Fold back about ½ inch of liner at one edge. Guide the patch through the tear with the adhesive facing the back of the torn fabric. Keep it clear of the opposite tube wall. Center the patch, line up the torn edges without overlapping them, and press the exposed strip against sound fabric.
- Pull out the liner as you press. Hold the liner by its folded edge and draw it slowly out through the opening. As the adhesive is exposed, smooth the raft fabric onto the patch a little at a time. Keep the patch relaxed. Once the liner is out, rub firmly from the center to the edges through the tube fabric.
- Cover the same tear from the outside. Center the second patch over the first, adhesive facing the outside of the tube. Peel back ½ inch of liner and anchor that edge. Draw off the rest of the liner as you smooth the patch down. Press out any air toward the nearest edge, then rub around the whole perimeter with your fingers or a smooth roller.
Let it bond, then check for leaks
Tear-Aid lists 1 hour for Type A and 24 hours for Type B to reach full adhesion. For a two-sided repair, start the clock when you press down the last patch. After that time, inflate the raft on shore to the pressure specified for your model. Check the edges and repeat the soapy-water test. Fresh bubbles that keep growing, a lifting edge, or continued pressure loss are reasons to keep the raft ashore and contact SOTAR service.
When to send SOTAR a photo
If you can see woven fibers through a scrape, or the patched tube still loses air, send us a close-up and a wider photo showing where the damage sits on the boat. Include the serial number if you have it. Our service team can help you decide whether the raft needs a welded fabric patch.
