{"product_id":"nrs-frame-cataraft-motor-mount","title":"NRS Frame Raft Motor Mount","description":"\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eThe Raft Motor Mount needs the Motor Mount Stern Side Rails (Item # 90022.02) and a piece of Frame Pipe, (Item # 91002.01) or a Stern Seat Mount (Item # 92017.03) to attach to your main frame. These are sold separately.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eAttach an outboard motor to the NRS Raft Motor Mount and your raft is ready for fishing or moving you through those long, flat stretches.\u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWe use our heavy-duty 1-5\/8\" OD 6061-T6 aluminum pipe to make the framework for the Motor Mount.\u003c\/li\u003e\n\u003cli\u003eThe 18\" wide transom plate is a piece of 2\" x 8\" wood\/plastic composite decking material that will not rot or deteriorate when exposed to water and sun.\u003c\/li\u003e\n\u003cli\u003eFour 3 3\/4\" motor mount U-bolts hold the transom plate firmly in place.\u003c\/li\u003e\n\u003cli\u003eIf you already have an NRS Stern Seat Mount, you can install your Motor Mount on the Seat Bar.\u003c\/li\u003e\n\u003cli\u003eIf you do not have a Stern Seat Mount you will need a pair of NRS Stern Side Rails (item #90022.02, sold separately) to link the Motor Mount to the rear Crossbar of your frame. We stock three sizes: 32\", 36\" and 39\". Measure the distance from the center of the rear crossbar to the center of the raft's rear tube. If you need a length other than those stock lengths, we will custom bend the size you need.\u003c\/li\u003e\n\u003cli\u003eIn our experience, a 10-hp motor is generally as large a motor as most boaters use. Even a 3-hp motor will move a raft along at a pretty good clip. Operating a raft at high speeds can be unsafe, and with a self-bailing raft will definitely result in water jetting up through the drain holes!\u003c\/li\u003e\n\u003cli\u003eAlways attach a safety rope or strap from your motor to the frame.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv class=\"frameSpecBlock\"\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eA\u003c\/td\u003e\n\u003ctd\u003eB\u003c\/td\u003e\n\u003ctd\u003eC\u003c\/td\u003e\n\u003ctd\u003eD\u003c\/td\u003e\n\u003ctd\u003eE\u003c\/td\u003e\n\u003ctd\u003eF\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e13 7\/8\"\u003c\/td\u003e\n\u003ctd\u003e10 1\/2\"\u003c\/td\u003e\n\u003ctd\u003e17\"\u003c\/td\u003e\n\u003ctd\u003e17 7\/8\"\u003c\/td\u003e\n\u003ctd\u003e7 1\/2\"\u003c\/td\u003e\n\u003ctd\u003e24\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp\u003eSupport arms are bent in toward boat at a 7 degree angle from the vertical.\u003c\/p\u003e\n\u003cdiv id=\"pdp-instructions\"\u003e\n\u003ch3\u003eProduct Instructions\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eAttach transom board to L-shaped bars, using the extra long Ubolts and backing plates supplied. Leave these finger tight.\u003c\/li\u003e\n\u003cli\u003eAttach top of L-shaped bars to stern mount bar as shown in picture. Place the U-bolts under the bar, then push the LoProTM fitting onto it. It may be necessary to bend the horns of the U-bolts so that they match the holes on the fitting. This small amount of bending can usually be done by hand.\u003c\/li\u003e\n\u003cli\u003eTighten the locking nuts. The washers are intended to take up slight variations in the length of the U-bolts. If less than two or three threads protrude above the top of the nylon-locking nut, do not use the washers.\u003c\/li\u003e\n\u003cli\u003ePosition the transom at the height needed for your motor and securely tighten the eight nylon-locking nuts from step 1.\u003c\/li\u003e\n\u003cli\u003ePeriodically check the tightness of all nuts and bolts. If these are loose, over time joints will become sloppy, or the transom may move.\u003c\/li\u003e\n\u003cli\u003eAlways secure your motor to the frame with a safety rope or strap to prevent loss of the motor if your motor clamps loosen.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/div\u003e","brand":"NRS","offers":[{"title":"Default Title","offer_id":28690228740180,"sku":"93100.01","price":219.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0729\/2837\/files\/Raft_Motor_Mount.gif?v=1737430368","url":"https:\/\/sotar.com\/es\/products\/nrs-frame-cataraft-motor-mount","provider":"SOTAR","version":"1.0","type":"link"}